This article provides instructions on both moving your Peloton Bike/Bike+ to a different property, as well as moving it from room-to-room.
Moving to a Different Property
Room-to-Room Moves
Moving to a Different Property
We highly recommend using a shipping or moving company that will insure your Peloton Bike/Bike+ just in case damage occurs during transport.
Regardless of who is moving the Bike/Bike+, to prevent any damage during the move, we ask that you remove the touchscreen, pedals, water bottle holder, and weight holders from your Peloton Bike or Bike+ prior to transport to reduce any damage to these parts. Below you will find instructions on how to do so.
We also suggest bringing the handlebars and seat post to the lowest position and ensuring all the adjustment levers on the Bike/Bike+ are fully tightened.
Touchscreen
| Removing and Reattaching Your Touchscreen |
| Bike Tutorial |
Bike+ Tutorial |
|
|
|
Tools Needed
- Phillips head screwdriver
- 4mm Allen Wrench
Removal Steps
- Power off the Peloton Bike and unplug the power cable.
- Open the plastic cable retention clip on the back of the touchscreen and disconnect all monitor cables.
- Remove the back panel on the rear of the touchscreen. Now you can access the (4) mounting screws and mounting plate.
- With a second person firmly holding the touchscreen, remove the (4) mounting screws with a Phillips head screwdriver.
- Remove the touchscreen and set it aside
Re-Installation Steps
- Carefully lay the touchscreen face down on a towel or mat. Remove the square panel from the back of the touchscreen.
- Set the mounting plate perpendicular to the monitor arm.
- Align the plate with the screw holes on the back of the touchscreen. Secure the touchscreen to the monitor arm using your Phillips head screwdriver and (4) bolts with washers.
- Snap the square panel back onto the touchscreen.
- Tighten the bolt at the side of the handlebar base using your 6mm Allen wrench. ⚠CAUTION: Make sure all bolts are tight before moving to the next step.
- Tilt the touchscreen forward and back to check for wobble between the touchscreen and mounting plate. If there is any movement, tighten each bolt again.
- Open the plastic cable retention clip at the back of the touchscreen. This may require some force.
- Locate the monitor cable at the left of the flywheel. Plug the cable connectors into the power and data ports. Make sure both connectors are fully seated, then close the clamp. Replace the Ethernet cable if applicable.
- Using the fastener strap, secure the cable to the monitor arm. Make sure there is enough slack on both sides of the strap to raise the handlebars to their highest position and to tilt the touchscreen up and down.
|
Tool Needed
Removal Steps
- Power off the Peloton Bike+ and unplug the power cable.
- Make sure the touchscreen is vertical and rotate it 180°. Then tilt it all the way up.
- Unplug the power/data and audio cables from the back of the touchscreen.
- Using a 4mm Allen wrench, remove the two touchscreen bolts from the monitor mount.
- Remove the touchscreen and set it aside.
Re-Installation Steps
- Add the touchscreen to the monitor mount and tilt it up.
- Return the bolts to the monitor mount. Take care to not strip the bolts
- Using a 4mm Allen wrench, tighten the bolts fully.
- Tilt the touchscreen vertical again and rotate it to face the back of the Bike.
- Plug the power/data cable into the middle port (the Peloton port) and the audio cable into the audio port.
|
Pedals
| Removing and Reattaching Your Pedals |
| Bike / Bike+ Tutorial |
|
|
|
Tool Needed
Removal Steps
- Turn resistance to maximum (Bike) or have a helper hold down the resistance knob (Bike+) to stop the crank arms from moving.
- Using a 15 mm pedal wrench, rotate the right pedal spindle counterclockwise until the pedal comes off.
- Rotate the left pedal spindle clockwise until the pedal comes off.
Re-Installation Steps
⚠ CAUTION: Identify the right and left pedals before installation. Make sure each pedal is correctly threaded before screwing it in. Misaligning the threads or turning a pedal in the wrong direction could damage the pedal and bike.
- Look for “L” and “R” markings on the pedals. Place the pedal marked L on the left side of the bike, and the pedal marked R on the right side of the bike.
- Insert the right pedal into the right crank arm at a 90° angle. Holding the pedal steady, rotate the spindle clockwise until it is hand-tight. Tighten using a 15 mm pedal wrench. It’s important that the pedal is as tight as you can make it.
- Insert the left pedal into the left crank arm at a 90° angle. Holding the pedal steady, rotate the spindle counterclockwise until it is hand-tight. Tighten using a 15 mm pedal wrench. Double check that the pedal is as tight as you can make it.
|
Weight Holders
| Removing and Reattaching Your Weight Holders |
| Bike / Bike+ Tutorial |
|
|
Bike Tutorial
Tool Needed
Removal Steps
- Remove any weights from the weight holder.
- Using a 4 mm Allen wrench, remove the (2) bolts and (4) washers on each side of the seat slider. Remove the weight holders from the Bike.
Re-Installation Steps
- Add first one spring washer and then one flat washer to each bolt.
- Hold the right weight holder against the right side of the seat slider and secure it using a 4mm Allen wrench and two bolts with washers.
- Add the left weight holder to the left side of the seat slider using the remaining two bolts with washers.
- Verify that the weight holders are secure.
- Return any weights to the weight holders.
|
Bike+ Tutorial
Tool Needed
Removal Steps
- Remove any weights from the weight holder.
- Unscrew the four screws attaching the weight holder to your Bike. Remove the weight holder.
Re-Installation Steps
- Place the flat part of the weight holder against the side of the seat slider so that the two sets of holes line up.
- Secure the weight holder with two bolts and the 4mm Allen wrench.
- Repeat with the other weight holder.
- Return any weights you removed.
|
Water Bottle Holder
|
Removing and Reattaching Your Water Bottle Holder
|
| Bike / Bike+ Tutorial |
|
|
|
Bike Tutorial
Tool Needed
Removal Steps
- Remove any weights from the weight holder.
- Using a 4 mm Allen wrench, remove the (2) bolts and (4) washers on each side of the seat slider. Remove the weight holders from the Bike.
Re-Installation Steps
- Add first one spring washer and then one flat washer to each bolt.
- Hold the right weight holder against the right side of the seat slider and secure it using a 4mm Allen wrench and two bolts with washers.
- Add the left weight holder to the left side of the seat slider using the remaining two bolts with washers.
- Verify that the weight holders are secure.
- Return any weights to the weight holders.
|
Bike+ Tutorial
Tool Needed
Removal Steps
- Remove any weights from the weight holder.
- Unscrew the four screws attaching the weight holder to your Bike. Remove the weight holder.
Re-Installation Steps
- Place the flat part of the weight holder against the side of the seat slider so that the two sets of holes line up.
- Secure the weight holder with two bolts and the 4mm Allen wrench.
- Repeat with the other weight holder.
- Return any weights you removed.
|
Room-to-Room Moves
The Peloton Bike/Bike+ has two wheels on the front stabilizers to make moving easier.
- Position yourself behind the Bike/Bike+. Grab the back stabilizers with two hands and lift the back of the Bike/Bike+ up to tilt it onto its front wheels.
- Carefully push or pull the Bike to its new location.
- Reassemble your touchscreen on the Bike (not applicable to Bike+).
Disclaimer: Damage or equipment failure resulting from disassembling, reassembling, or moving the Peloton Bike/Bike+ will not be covered under Peloton's warranties. By undertaking disassembly, reassembly, or the relocation of your Peloton Bike, you agree to waive and release Peloton from any and all claims that you may have resulting from the disassembling, assembling, or moving of the Peloton Bike by anyone other than a Peloton authorized Service Technician.
